Corvette CV Joint Boots

Though they may not seem like much your C5 or C6 Corvette’s Inner & Outer CV Joint Boots play a key role in keeping your Corvette on the road. They are prone to cracking or splitting, which can have multiple negative effects on the drive-ability of your Corvette. Besides allowing contamination into the CV joint itself and causing premature wear of the bearings, cracked CV joint boots allow grease to be slung out of the boot, which can saturate your Corvette’s Brakes.  This would not only cause an increase in braking distances but can also ruin your Corvette’s brake pads and rear rotors. If you have replaced your Corvette’s rear brake components or upgraded to performance brake pads & rotors, you know that brake rotor and pad replacements can get very expensive.

Until now the only sure way to avoid damage from bad CV joint boots was to replace the expensive CV axle shaft, which comes with new inner and outer CV joint boots. With the recent addition of our C5 & C6 Corvette Inner & Outer CV Joint Boot Kits you can now replace your Corvette’s CV joint boots without spending hundreds of dollars for the entire axle shaft. We have inner and outer CV joint boots for all C5, C6, Z06, Z51, Grand Sport, & ZR1 Corvettes. Each kit includes one inner or outer boot, clamps, & the correct amount of grease to replace a single boot.

C6 Corvette Mamba Air Intake

The Mamba Corvette Air Intake takes advantage of it’s design by squeezing as much air as possible into the throttle body without the use of a Corvette Supercharger. The Mamba’s air filter is one of the largest in the Corvette aftermarket industry and was custom designed by Zip for maximum airflow. The Mamba has shown dyno proven power improvements of 20+ rear wheel horsepower when utilized with the Mamba Fresh Air Scoop. The Mamba Air Intake is a direct bolt on for all C6 Z06 Corvettes and 2008-2009 LS3 equipped Corvettes. If used in conjunction with the fresh air scoop, PCM programing will be required on 2008-2009 LS3 equipped Corvettes due to the increased amount of air flow.

Early C6 LS2 equipped Corvette owners can retrofit the Mamba Air Intake by using our mass air flow sensor adapter harness, mass air flow sensor, and power coupler. Due to the large amount of forced air, LS2 Corvettes will also require custom PCM programming of the mass air flow table.

The easiest solution for protecting your Corvette’s interior from the extreme heat and sunlight is to install a Corvette Sunshade. You can purchase very cheap sunshades from a local auto parts store but the fact is that they are not custom made to fit a Corvette and they simply do not look as nice as our Corvette Sunshades. We offer sunshades for C4, C5, and C6 Corvettes all of which come with the Corvette logo and are custom made to fit your Corvette.

C4 Corvette Sunshade

This C4 Corvette Cool Shade is specifically designed for 1984-1996 Corvettes. It’s reflective nylon surface effectively blocks rays to reduce heat build-up and prevent fading. The 1-piece lightweight coil frames twist closed to a compact 9″ for easy storage. To clean this sunshade simply wipe down with a damp towel or sponge. Sunshade includes “Corvette” script on one side and a C4 Corvette logo on the other.

C5 Corvette Sunshade

This 2-pc C5 Corvette Cool Shade is designed to fit 1997-2004 Corvettes. Like the C4 sunshade the Reflective nylon surface effectively blocks rays to reduce heat build-up and prevent fading. Each panel measures 28″ x 32″ and includes a screen printed “Corvette” script and a C5 Corvette logo. Simply wipe the sunshade with a damp towel or sponge to keep clean.

C5 Corvette Sunshade

This 1-pc C5 Corvette Sunshade will fit your Corvette’s windshield perfectly. The sunshade is triple laminated constructed and has a reflective outer layer, which blocks direct sun and protects the interior surfaces from heat build-up and fading. The sunshade features a C5 logo and sewn-in Velcro straps for compact storage.

C5 Corvette Sunshade

This folding accordion C5 Corvette Sunshade design is custom fit specifically for 1997-2004 Corvettes. It fits into the corners of the windshield blocking the sun completely from the dash, which will reduce interior temperature and protect your Corvette’s  interior from the sun’s rays. Your sunvisors hold the shield in place. One side of the shade is made of a silver reflective fabric and the other side is finished in soft felt. Both fabrics are laminated to a form core board, which acts as an insulator to help reduce heat build-up inside your Corvette. This C5 Sunshade includes a C5 Corvette logo on the front.

C6 Corvette Sunshade

Protect your C6 Corvette’s interior from harsh sunlight with this C6 Corvette Cool Shade. The reflective nylon surface effectively blocks rays to reduce heat build-up and prevent interior fading. The 2-piece design includes a screen printed “Corvette” script and C6 Corvette logo. Each panel measures 28″ x 32″. Simply wipe with a damp towel or sponge to keep clean.

C6 Corvette Sunshade

The Ultimate Insulated windshield sunshade for C6 Corvettes is a folding accordion design custom fit specifically for C6 Corvettes. It fits into the corners of the windshield blocking the sun completely from the dash, which helps reduce interior temperature and protect your Corvette’s interior from the sun’s rays. Your sunvisors hold the shield in place. One side of the shade is made of a silver reflective fabric and the other side is finished in soft felt. Both fabrics are laminated to a form core board, which acts as an insulator to help reduce heat build-up inside your Corvette. Sunshade includes a C6 Corvette logo on the front.

By using one of our Corvette sunshades in your Corvette you could prevent fading, cracking, and other problems the sun’s rays will cause. Don’t mistreat your Corvette’s interior any longer; start using a sunshade today. We also carry Corvette Rear Cargo Shades and Corvette hatch vents to help keep your Corvette cool in the summer heat.

Corvette Power Steering Pulley

Zip Corvette’s very own Billet Power Steering Pulley replaces the stock pulley with a much more dependable, better looking part. Machined from 6061-T6 Billet Aluminum, this 10 spoke highly polished pulley will add brilliance to the front of your Corvette’s Engine. With the addition of this pulley you will be able to add the performance modifications of your choice, without the result of a broken power steering pulley. Exclusive to Zip Corvette, this pulley is manufactured in the United States and will install on C5 & C6 Corvettes.

Another excellent Corvette Part at a low price, exclusively from Zip Corvette.

94-96 Corvette MSD Spark Plug Wires

1992-1996 LT1 & LT4 Corvette: The MSD 8.5mm Super Conductor Wire is “the” performance wire for C4 Corvettes. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 12 inch length of Super Conductor Wire there is only 40 – 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, MSD uses a copper alloy conductor due to its great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference (EMI) “choke”. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your Corvette. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears.

92-96 Corvette MSD Blaster Coil

1992-1996 LT1 & LT4 Corvette: These MSD Ignition Coils include the patented MSD performance enhancements inside a factory style housing! MSD designed these Coils by combining their Blaster Coil experience with E-core coil efficiency. Each coil has a unique turn ratio plus there is lower primary resistance than the stock Corvette coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped Corvettes.

92-96 Corvette MSD Cap & Rotor

1992-1996 LT1 & LT4 Corvette: MSD’s all-out performance distributor replaces the OEM LT1 Optispark distributor! They machine an entire billet block of aluminum down into a precise housing that fits in place of the factory piece. Then, MSD fills it with a reliable new pick-up assembly, a trick timing adjustment mechanism and new distributor cap! The pick-up is an advanced optical encoder, a different style of optical pickup than the OEM. This type of pick-up has proven to be very reliable and stable through extreme rpm and conditions. The rotor is bolted to a drive assembly that is indexed to the shaft and is stabilized through the use of a large ball bearing assembly. Once installed, you have the ability to adjust the ignition timing. An adjustment screw allows the timing to be modified up to +/-5°. The distributor is equipped with a fresh air vent and has an extra thick mounting surface for the cap to eliminate leaks. The distributor is supplied complete with their heavy duty LT1 cap, rotor and the components required for installation. View installation instructions for 1992-1994 Corvette Optispark Distributors or 1995-1996 Corvette Optispark Distributors.

1997-2009 MSD Spark Plug Wires

1997-2009 Corvette: The MSD 8.5mm Super Conductor Wire is “the” performance wire for C5 & C6 Corvettes. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 12 inch length of Super Conductor Wire there is only 40 – 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, MSD uses a copper alloy conductor due to its great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective Electro Magnetic Interference (EMI) “choke”. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your Corvette. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears.

1997-2004 LS1/LS6 MSD Coil Set

1997-2004 LS1 & LS6 Corvette: MSD Ignition’s Multiple Spark Coils (MSC) will fit in place of the stock Corvette coils and connect directly to the factory connectors. Once installed, you will have the power and performance of higher energy sparks, crowned with MSD’s multiple spark discharge. Increased spark energy and voltage, along with multiple spark capabilities help improve the combustion process of the fuel mixture to create an efficient burn. This results in improved throttle response, smooth idle and quick starts, plus increased high rpm performance!

2005-2009 MSD Multi-Spark Coil Set

2005-2009 Corvette: There is now an MSD performance replacement coil for the popular LS2 Corvette Engine. The complex electronic controls of the original coils presented the aftermarket with a challenge as the drivers that control the firing of the coils are built into the OE models. MSD engineers were able to design an advanced circuit that will operate with the factory electronics of the C6 Corvette engine controls while producing a higher output spark. Not only do you get a higher voltage spark, but the coil will deliver multiple sparks. Notice that the coil has two connectors molded into the custom housing. One accepts the factory coil connector; the other is for an upcoming ignition controller. (This controller is still in the development stages but it will allow you to program functions of the ignition.) The new coils mount in place of factory LS-2 coils.

MSD is just one popular brand name sold at Zip Corvette. To view all MSD products as well as all other Corvette brands including Adam’s Polishes, Corsa, Kooks, Fidanza, Wilwood and much more click here.

C6 Corvette Black-Out Kits

Zip also carries Black-Out Kits for C4 and C5 Corvettes as well. These kits are made of the same acrylic as the C6 Corvette Black-Out Kits, which will not affect the view of the Corvette’s brake lights when the brake pedal is depressed. Click here to see all of our Corvette Black-Out Kits or here if you would like to order a free Corvette Parts & Accessories Catalog that comes packed with tons of popular Corvette parts just like this.

With a 100% stock 1984-2009 Corvette, the factory radiator will work efficient enough to keep the car running cool. As soon as you begin modifying your Corvette, you are going to push the factory radiator beyond its limits. The reason for radiator failures in modified Corvettes is a result of the single row core design. The end tanks were made of plastic and held in place with small crimp tabs and a neoprene rubber gasket was used to seal the tanks to the core. Frequent end tank failures and gasket leaks are just a few of the common problems associated with factory radiators installed in modified Corvettes. For complete assurance that your next radiator will not fail, consider a Direct Fit Aluminum Radiator. They feature press formed end tanks that are tig welded directly to the double row core, providing a permanent seal.

Stock Single Row vs. Direct Fit Double Row Radiator

Zip Corvette offers the best Direct Fit Radiators on the market for C4, C5, & C6 Corvettes. Our Corvette Direct Fit Aluminum Radiators are just what the name implies; a direct fit. Many companies offer replacement Corvette radiators that are considered “direct fit”, but in fact, most require some alterations. True Direct Fit radiators are designed to install into the stock mounting and use the factory connections without any modifications or adapters. Each Direct Fit Radiator starts with a USA made core that is furnace brazed in a force nitrogen furnace. They feature two rows of 1″ cooling tubes (which will help double the cooling capacity of stock radiators), a serpentine fin and are epoxy free. Each Direct Fit tank is manually tig welded by expert craftsmen, providing the ultimate in strength and appearance.

From the earliest C4 to the latest C6, Zip has a Direct Fit Aluminum Radiator to match your Corvette. If you would like to install a Direct Fit Radiator but you want to keep your Corvette looking as original as possible, then simply have the radiator coated with ”Black Ice”. This Black Ice paint is applied to the outer surfaces of the radiator only, so the cooling tubes and any other components inside the fin material are not affected. Tests show that the Black Ice Coat will not disrupt the cooling process therefore allowing the Direct Fit Radiator to continue to out-perform all of its competition.

If you have had trouble finding a quality C4 Corvette Radiator read, on about Zip Corvette’s Direct Fit Radiators; we have them available for all 1984-1996 Corvettes with both automatic and 6-speed transmissions. Also available to purchase for 1990-1996 Corvettes are Direct Fit Radiators with an optional, built in Engine Oil Cooler. No extra modifications are required for this radiator and all installation instructions are included.

C5 Corvette Direct Fit Aluminum Radiator

The stock LS1 and LS6 engine will thrive with a new C5 Corvette Direct Fit Aluminum Radiator from Zip Corvette. They are available for all 1997-2004 Corvettes with both automatic and 6-speed transmissions. If you would like to add an engine oil cooler to your C5, Zip can offer that as well. Purchase a Direct fit Radiator with the EOC option and the separate Engine Oil Cooling Kit which includes necessary adapters, hoses and fittings to complete the installation. With the EOC option, your C5 Corvette will be able to keep the engine oil running at optimal operating temperatures.

• The first is a direct replacement for the 2005-2009 non-Z51 6-speed transmission. This radiator does not have the engine or transmission oil cooler option.
  

  C6 Corvette Direct Fit Aluminum Radiator W/EOC

• The second Radiator is for the 2006-2009 Z06, 2005-2009 Z51 automatic, and 2007-2008 Z51 A6 equipped Corvette. This radiator includes the transmission cooler but not the engine oil cooler option.
• The third Direct Fit Radiator includes a factory style engine oil cooler only. It is a direct replacement for 6-speed non-Z51 Corvette owners who want to add an engine oil cooler. This radiator includes a high performance 7 plate aluminum engine oil cooler with 3/4-16 SAE oil ports which are identical to the factory GM radiator. You can use the factory GM oil line assembly (quick connection fittings required) or install the #10AN fittings (included) and use stainless steel hose assemblies.
• The last C6 Direct Fit Radiator offered from Zip Corvette Parts is a direct replacement for 6-speed or automatic Z51 equipped Corvettes. This radiator includes a factory style transmission and engine oil cooler.

Corvette Dual Fan Upgrade Kit

Another great cooling system upgrade to any C4, C5 or C6 Corvette is a Dual Fan Upgrade Kit. These upgrade kits will boost air flow up to 40% over stock allowing your Corvette to run cooler then ever. The C4 Dual Fan Upgrade Kits are available to fit both the factory radiator and the Direct Fit Aluminum Radiators in 1990-1996 Corvettes. All required relays and wiring is included. The C5 Dual Fan Upgrade Kit fits all 1997-2004 Corvettes. It is designed to fit both the factory radiator and a new Direct Fit Aluminum Radiator. Note that the electrical connectors are different than factory fans and splicing will be required for installation of this kit. The C6 Dual Fan Upgrade Kit fits all 2005-2009 Corvettes with a Direct Fit Aluminum Radiator. This kit like others includes all relays and wiring for a complete installation.

Borla Performance Exhaust

Borla has always used the transfer of technology from racing to the street as a tool. Exhaust engineering is a science with which Borla has more experience than anyone in the aftermarket. Their straight-through and multi-core designs increase exhaust velocity to move more air through your Corvette’s engine. Exhaust gases evacuate the cylinder completely, allowing the new charge to come into the cylinder, thereby creating more power. The actual horsepower increase depends upon the fuel management system’s ability to provide the right amount of fuel to match the extra airflow, but generally 7 to 15% increases for Corvettes are typical.

The following are some of the Borla Performance Corvette Exhaust Systems available for your C4, C5, C6, or Z06:

1986-1991 Borla Stinger Exhaust System

Borla Performance introduces a new system for the celebrated 1986-1991 C4 Corvette equipped with a 5.7L V-8 engine. Borla has engineered this Cat-Back system to work with either the popular manual transmission or the automatic. The aircraft-quality T-304 stainless steel system is easy to bolt on, is a direct replacement for the much heavier (by some 20lbs.!) stock system and is based off the big brother C5/Z06 system known as the “Stinger”.

A 3″ diameter front pipe is mounted just after the catalytic converter leading to a Y-pipe, which splits into two 2-1/2″ pipes exiting on each side of the rear. The muffler and tip assembly use a 10″x 5″ diameter round muffler on each side of the vehicle, with a polished rectangular, rolled edge, angle cut tailpipe tip at each exit.

Tests have shown an exciting 41% increase in flow for dramatic improvement in power and fuel economy. That famous and aggressive Borla growl and great look proclaim this block may be small, but it means all business – Borla guarantees it for a million miles!

1997-2004 Borla Stinger Exhaust System

Borla’s C5 performance exhaust systems are available in 4 different styles. There is the Borla Stinger with 4″ Dual Tips, Borla Stinger with Quad 4″ Oval Tips, Borla Stinger with Quad 4″ Round Tips, and the Borla XR-1 Racing Exhaust System with Round Tips.

The “S-Type” commonly referred to as the “Stinger” has a smaller, round muffler with a center-in/center-out configuration giving a more aggressive sound and higher flow. This allows for high velocity and uninterrupted air flow which are two main ingredients when it comes to increasing your Corvette’s performance.

1997-2004 Borla XR-1 Race Exhaust System

The XR-1 performance exhaust system is a race exhaust system that reflects the style and performance your C5 Corvette deserves. It includes 2 1/2″ XR-1 center resonator and mandrel bent T304 stainless tubing for superior performance, increased flow, increased torque and up to a 10% horsepower gain. Its beefy 4 1/2″ rolled edge tips are each embossed with a patented Borla logo.

2006-2009 Z06 Borla Stinger II Exhaust System

The Stinger II, as with the C5 Corvette Stinger Exhaust System, has a round muffler with a center-in/center-out configuration giving a more aggressive sound and higher flow. This allows for high velocity and uninterrupted air flow which are two main ingredients when it comes to performance making.

If you are looking for the performance side of the 100% bolt on Stinger II Exhaust System but not quite all of the aggressive sound, Borla’s Touring Exhaust Systems are the answer for you. By designing virtually the same system just with a larger case (notice the smaller case in the above Z06 image and the larger case in the image below), Borla is able to quiet the system without sacrificing horsepower gains.

2006-2009 Z06 Borla Touring Exhaust System

Borla Performance Exhaust Systems are sharp looking, long lasting, and performance oriented. Any C4, C5, or C6 Corvette owner interested in upgrading the stock exhaust should consider what Borla has to offer. It will be tough to find a simple bolt on installation that provides the performance and great sound a Stinger, Touring, or XR-1 Exhaust system brings to the table. Borla: The world’s most winning exhaust.

Pfadt Racing Inverted Adjustable Shock Absorber Set

Pfadt Racing has designed several performance street and track Corvette parts for your C5 or C6. Since every Corvette owner is not looking for the same experience from their car, Pfadt Racing has designed their line of product to offer the ultimate in adjustability and performance. If you are looking to add better handling in an everyday driver or competition style steering and response for serious track use, Pfadt Racing has the answer for you. To see all of the Pfadt Racing performance Corvette Parts available from Zip Corvette click below to read the rest of this article.

1997-2009 Corvette Adjustable Sway Bar Package

Are you looking for race quality products that do not beat you up on the street? Pfadt Racing Sway Bars are the easiest way to perfect the handling of your C5 or C6 Corvette without sacrificing ride quality. These Pfadt Racing Sway Bars are adjustable in both the front and rear to tune your handling. They are designed to bolt in for easy installation, and set up to reduce your Corvette’s tendency to push in the turns. Pfadt C5 and C6 Sway Bars are significantly lighter than both stock and after market bars weighing just 9.5 pounds. 4 pounds lighter than stock!

1997-2009 Corvette "Pfatty" Competition Adjustable Sway Bar Package

Pfadt’s “Pfatty” Adjustable Sway Bar for C5 and C6 Corvettes is the alternative to running the super stiff T1 sway bars. The front bar measures 38mm in diameter, same as the GM T1 sway bar. The rear sway bar measures 28mm; both sway bars feature adjustable ends so the suspension can be softened if desired. Pfadt “Pfatty” Adjustable Sway Bar Package is recommended for serious track use. You will be thrilled with the reduced body roll and stability in the turns!

1997-2004 Corvette Engine Oil Cooler Kit

High horsepower or hard-core track days can be hard on engine oil temperatures. This 1997-2004 Corvette Oil Cooler Kit can reduce engine oil temperatures up to as much as 60 degrees. It also includes lightweight ducting to direct the maximum amount of air to the stand-alone cooler, braided stainless steel lines with pre-assembled AN fittings, billet aluminum oil block, and attaching hardware.

1997-2004 Corvette Transmission Brace & Mounts

Hold the powertrain in place with Pfadt’s uniquely designed transmission brace. This mount reduces the massive powertrain shake (sometimes mistaken as wheel hop) that is common in the C5 Corvette. Pfadt’s Transmission Brace is an excellent solution for high horsepower or performance driven Corvettes. It bolts to the differential to limit powertrain movement and reduces the load on your half-shafts and other driveline components. The Transmission Brace is constructed with 6061 T6 aluminum and anodized for maximum durability. You can couple this transmission mount with Pfadt’s C5 Engine Mounts for an unbeatable package.

1997-2009 Corvette Adjustable Coil Over Shock Kit

Pfadt C5 & C6 Corvette Coil Overs are engineered for exceptional street driving and track performance. Unlike some coil overs, Pfadt’s allow you to adjust ride height independent of spring pre-load so you do not have to compromise ride quality for ride height. Pfadt’s coil overs also feature a compression and rebound dampening adjustment that can be tuned while the suspension is on the Corvette. The shocks are a monotube design for simplicity and durability and are fully rebuildable. Pfadt 1997-2009 Corvette Adjustable Coil Over Shock Kit is a pure bolt on upgrade and fits C5 & C6, standard or Z06 equipped Corvettes.

1997-2009 Corvette Inverted Adjustable Shock Absorber Set

If you are looking to upgrade your Corvette’s shocks but not looking to make the change to coil overs, these Pfadt Inverted Adjustable Shocks are perfect for your Corvette. Pfadt has designed an adjustable shock that will allow you to “turn it up” for track use or “dial it down” for street use, without tools and without removing the shocks from your Corvette.

1997-2009 Corvette Camber Adjustment Kit

Pfadt’s C5 & C6 Corvette Camber Adjustment  Kit allows you to achieve the maximum negative camber and eliminates the eccentrics so that the settings do not slip. This kit replaces the bolts on the front upper a-arms with stainless steel studs and Pfadt provides stainless steel shims to set your desired camber and caster. The lower eccentrics are eliminated and the bolts are locked into their maximum position using a set of off-set plates. For the rear Pfadt provides a set of shims for the eccentric to dial in your alignment and make it stick.

2006-2009 Z06 Corvette Camber Adjustment Kit

Pfadt’s C6 Z06 Corvette Camber Adjustment  Kit allows you to achieve the maximum negative camber and eliminates the eccentrics so that the settings do not slip. This kit replaces the bolts on the front upper a-arms with stainless steel studs and Pfadt provides stainless steel shims to set your desired camber and caster. The lower eccentrics are eliminated and the bolts are locked into their maximum position using a set of off-set plates. For the rear Pfadt provides a set of shims for the eccentric to dial in your alignment and make it stick.

2006-2009 Z06 Corvette Polyurethane Control Arm Bushing & Shaft Kit

The complete Pfadt Polyurethane Control Arm Bushing Kit with new aluminum shafts & sleeves is designed to quickly replace all of your Corvette’s factory rubber bushings with new polyurethane bushings. Polyurethane bushings maximize your suspension’s performance by delivering quicker steering response and predictable handling in all driving modes. Complete Pfadt Polyurethane Bushing Set includes rear spring cushions, front control arm bushings, and rear control arm bushings PLUS new shafts and retainers for a quicker installation. This Pfadt Control Arm Bushing and Shaft Kit fits all C6 Z06 Corvettes.

Purchase Pfadt Racing products online at Zip Corvette Parts

• 1997-2004 Corvette Adjustable Sway Bar Package
  
• 1997-2004 Corvette “Pfatty” Competition Adjustable Sway Bar Package
• 1997-2004 Corvette Engine Oil Cooler Kit
• 1997-2004 Corvette Transmission Brace and Mounts
• 1997-2004 Corvette Bolt-In Rollbar (Uncoated)
• 1997-2004 Corvette Bolt-In Rollbar (Powder Coated Black)
• 1997-2009 Corvette Adjustable Coil Over Shock Kit
• 1997-2009 Corvette Inverted Adjustable Shock Absorber Kit
• 1997-2009 Corvette Camber Adjustment Kit
• 1997-2009 Corvette Sway Bar Pillow Blocks
• 1997-2009 Corvette Engine mounts
• 2005-2009 Corvette Adjustable Sway Bar Package
• 2005-2009 Corvette Competition Adjustable Sway Bar Package
• 2005-2009 Corvette Transmission Mounts
• 2005-2009 Corvette Bolt-In Rollbar (Uncoated)
• 2005-2009 Corvette Bolt-In Rollbar (Powder Coated Black)
• 2006-2009 Z06 Corvette Camber Adjustment Kit
• 2006-2009 Z06 Corvette Polyurethane Control Arm Bushing & Shaft Kit

This new Powr-Flow Mass Air Sensor is now available from Zip Corvette Parts for 2006-2007 C6 Z06 Corvettes. This Jet Performance Products’ mass air flow sensor is an excellent upgrade for your Corvette’s Z06 engine. Unlike the factory Corvette air flow sensor, which is a major restrictive point in both stock intake systems and aftermarket cold air intake systems, this  Powr-Flow Mass Air Sensor generates greater horsepower, torque, and gas mileage for your Z06 Corvette. On top of providing instant performance boosts for your Z06 Corvette, the Jet Powr-Flow Mass Air Sensor installs virtually hassle free in about 10 minutes.

Jet Powr-Flow Mass Air Sensor

Jet’s mass air flow sensor is an excellent upgrade for 2006-2007 Z06 Corvettes. Combine this sensor with a Callaway Honker or Vortex Rammer cold air induction system and your Z06 Corvette will be flowing cool air at a maximum. The combination of either cold air intake system and this air flow sensor could add up to 25 horsepower to your Corvette.

The newest Corvette Blackwing cold air package is now available from Zip Corvette Parts. The cold air intake is designed to increase and improve air flow, yielding more horsepower and a cleaner air intake system.

Blackwing Cold Air Package

The Blackwing air intake system out-flows the factory setup by as much as 90% and can provide up to +10 additional horsepower and +11 ft/lbs at the flywheel. The Blackwing uses a wire-reinforced, reusable and washable blue high-flow filter media which features an exclusive built-in flow indicator that changes color when cleaning is required. Also included in the package is a factory style finished high-volume air bridge with integrated MAF housing and secure mounting points. The new Blackwing cold air package installs on C6 Corvettes with no modifications or cutting required. All necessary hardware is included. The Blackwing filter cleaning kit is recommended with purchase for optimal cleaning and re-oiling as necessary.

1997-2009 Poly Suspension Bushing Completion Kit

The time involved to burn and/or cut off the old bushings, clean the parts and then re-use them can quickly prolong a job that should take 4-5 hours for installation and turn it into 8-10 hours. Zip’s exclusive Corvette shaft & sleeve kit replaces all the aluminum components with new steel components for a quicker polyurethane bushings installation. In doing so, at least 1/3rd of the labor time to install poly bushings in your C5 or C6 Corvette will be saved. The combination of poly bushings & the steel components in this kit is stronger and more responsive than stock, preparing your car for a day at the track, or for a drive down the street.

New C6 carbon fiber door handle covers are now available from Zip Corvette! They are molded into the same shape as the original GM design but have been overlayed with a UV protected high gloss carbon fiber finish.

C6 Corvette Carbon Fiber Door Handle Covers

As many Corvette enthusiast already know, attention to detail can make a difference on the show field. These carbon fiber door handle covers will without a doubt separate any Corvette from the pack. Door handle covers are Made in the USA. Follow along as we install a new set of these Corvette Door Handle Covers:

C6 Door Handle Installation instructions: With the introduction of the new C6 Corvette, GM created the finest automobiles available, however it seems they left the door open for a few personalized improvements. So what better way to improve the looks of your Corvette than with GM’s own line of bolt-on accessories? Follow along and we will show you just how easy it can be for you to transform your Corvette’s door handles into something to talk about.

Note: All C6 Corvettes come with flat black door handles regardless of the exterior color

01: Remove the two Phillips screws on the backside of the handle.

02: Once the screws are removed, carefully pull back on the bezel just enough to remove it from the door.

03

04: Now carefully push the door opening switch out of the bezel.

05: This is the door opening switch assembly.

06: With the new bezel in hand you need to push the switch into the new bezel. This may be a little harder then the original bezel since it is overlayed. Just apply a little pressure to the switch and it will lock into the bezel.

07: Install the bezel on the door by placing the lip of the bezel on the outside of the door first. Using light pressure push the bezel until it fully seats in the door.

08: Re-install the two Phillips screws that you removed from the original bezels.

09: This is the door bezel installed.

10: Final shot of the door bezel.

11: Final shot of the door bezel.

Now available to purchase online from Zip Corvette Parts:

C6 Corvette Carbon Fiber Door Handle Covers

New C6 Corvette LED Tail Light Kit now available from Zip Corvette. LED tail light kit is the perfect update for your C6 or Z06 Corvette providing you with brighter, longer lasting, and better looking tail lights. The kit is available in red or blacked-out versions and installs easily with no modifications required. Installation instructions and a three year warranty are included with purchase.

05-09 LED Tail Light Kit

The newest C6 Corvette exterior accessories on the market are now available from Zip Corvette. The laser mesh stainless steel inserts, manufactured by American Car Craft, are perfectly laser cut into a precise diamond mesh pattern. Once cut they are then hand tooled and specifically engineered to achieve the sparkle and glitter that every Corvette should possess.

C6 Laser Mesh Exterior Accessories

C6 Laser Mesh Exhaust Port Filler Panel

C6 Laser Mesh Driving Light Covers

C6 Laser Mesh Side Fender Grills

C6 Side Spears W/Fender Grills

C6 Z06 Laser Mesh Air Dam Grills

C6 Z06 Laser Mesh Light Covers

C6 Z06 Exhaust Port Filler Panel

C6 Z06 Laser Mesh Hood Vent Grill

C6 Z06 Laser Mesh Side Fender Grills

C6 Z06 Laser Mesh Side Fender Rear Grills

Installing laser mesh stainless steel is one of the easiest ways to spice up your Corvette’s exterior. Unlike other accessories of this sort which are constructed of a wire mesh material, ACC’s Corvette laser mesh is a premium 304 stainless steel that will never tarnish, pit or loose its luster. With no modifications necessary to install, you will drive away leaving everyone admiring the “little things” about your Corvette. Laser mesh options are available for both C6 and Z06 Corvettes and include: light covers, exhaust port filler panels, front grills, air dam grills, fender grills, hood vent grills, and rear vent grills. See images below for details.